# 1
Draw-Tite Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/2" Long - 7.5K
Excellent quality, fast shipping. Finding a metric ball for our international application was a bit difficult. We knew etrailer was the place to go for all things "trailer" related. Very happy with the purchase!
Strong and seems to be well made and well finished. One-inch ball mounting hole. I used this for a Curt hitch mounted on a 2014 Forester and pulls a small Harbor Freight trailer. Perfect height and trailer is level. Warning - don't get their hitch pin, it does not have a hole for a cotter pin, only a weak clip that I would not trust.
# 2
Convert-A-Ball Ball Mount for 2" Hitches - 8-3/4" Rise - 10" Drop - 8,000 lbs
Works great. Needed the drop to tow a utility trailer at level.
As always etrailer has the best products, best information and customer service, plus fast shipping! Thank you again!
# 3
Flash Secure Adjustable 2-Ball Mount w Chrome Balls - 2" Hitch - 6" Drop, 7" Rise
Very strong, easy to install and very secure. Yes a bit pricey, but well worth the money. I did notice there was what I thought was an unusual amount of play in the receiver. I called etrailer and Marcia was so very helpful and very concerned that I may have received the wrong product. She even called the manufacturer and found out what the changes that were made by the manufacturer which made the pictures incorrect. My hat is off to Marcia and all the folks at etrailer
ball mount fits loosely in the receiver so that the pins that extend out from the ball mount shaft through the holes in the receiver don't extend out far enough, for my liking. This is because since the ball mount shaft has so much play, it will shift to one side. Then, the pin on the other side does not extend all the way out of the hole so that it is not flush. True, i am being paranoid. However, i imagine a case like a crash where enough force could pull the shaft out from the not fully extended pin side to release the trailer to wreak more damage. I would just feel more secure if the pins went out further through the receiver or the shaft was not so loose. Otherwise, i really like the product a lot... enough to give it four stars... :o)
# 4
Convert-A-Ball Ball Mount for 2" Hitches - 6-3/4" Rise, 8" Drop - 10,000 lbs
I use this hitch when I pull my horse trailer to make the stop/start transitions as smooth as possible for the horses in the back. It works great. I also love that its a category IV hitch. Really heavy duty. My truck sits pretty high, and the amount of drop - 8" is perfect. I never worry about hitch failure travelling with my horses - they're a heavy load, and any failure would be a disaster. E Trailer provided excellent service, and their shipping to Canada was prompt and hassle free. Way to go guys, keep up the great work!
I have a 2012 GMC Sierra HD with a 12" suspension lift. I recently purchased a ball mount hitch with 8" inch drop for our 36' RV trailer and it worked great. It took 3 days for the hitch to get to me. Great service from e-trailer.
# 5
Convert-A-Ball Ball Mount for 2" Hitches - 10-3/4" Rise, 12" Drop - 7,000 lbs
Not that many non-adjustable option for a 12” drop and this one is the best! Love the cushion and it’s very strong. I put that to the test today when I got rear ended with it in the back of my truck. This thing saved the back of my Ram. Came right back to etrailer and ordered a new one!
Needed a large drop hitch to pull my car trailer. This item came quickly and worked perfectly.
# 6
Curt Multi-Ball Adjustable Ball Mount for 2" Trailer Hitches
Picked up my teardrop in ABQ on 2/17/23, and the Curt ball mount lined up perfectly with no drop/rise, and the extra length gave clearance for my rear door mounted spare tire. This mount is a beast, and the "overbuilt" nature of it gave me confidence that my Bronco would tow the teardrop easily. I also got the Curt Echo wireless brake controller, which synced easily to my phone and was easy to install, set up, and use. Overall a great towing experience, thanks to etrailer and Curt!
Works great used for 3 different trailer we have handy it's heavy well made.
# 7
Curt Multipurpose Ball Mount with 2" Receiver for Bike Racks and Cargo Carriers - 7,500 lbs
I am using the hitch for a car dolly and a bike rack. The fit is a little loose for the bike rackmI'll see it really works when get on the road.
Quality is excellent. However, it did not work so I am not sure what to do with it. I thought I could use the top hitch for a Bike rack and pull a utility trailer with other toys. The trailer is too close to make a turn so good try but not able to use it. Thank you for asking. I did not open the box for a while because I was having the trailer worked on so assumed I waited too long to return.
# 8
Ball Mount Adjustable with Sway-Control Tab, 6,000 lbs
The ball mount did not fit onto the shank. This was a very disappointing experience.
The fit of the U channel for the ball mount was too tight over the verticle drilled box tube. It needed “persuasion” to get it over the tube. This will make height changes away from the shop difficult. No rattle though.
# 9
MaxxTow Ball Mount w/ 2" Accessory Receiver - 2" Hitches - 2-1/4" Drop - 5,000 lbs
Heavy duty , very good quality.
# 10
Flash Simple 2-Ball Mount w Chrome Balls - 2" Hitch - 6" Drop, 7" Rise
Works great. With all the adjustments we can get our trailers to haul level now. Quality looks really good and it has the 2 size trailer hitch balls which makes it way more convenient.
VERY HAPPY, BUT STARTED TO SEE SOME RUST ON THE HITCH BALL AND ONLY USED TWO TIMES. THE VERSABILITY OF THE PRODUCT IS GREAT. OTHER THAN THE SMALL AMOUNT OF RUST ON THE BALL ITSELF, IM VERY SATISFY AND WILL BUY FOR MY OTHER TRUCKS.
# 11
Draw-Tite Ball Mount for 2" Hitch - 7" Rise, 8" Drop - 9-1/2" Long - 12,000 lbs
Heavy Duty Drop Down Hitch no problem pulling a 10,000# trailer
It fits perfect on my f350 diesel, super heavy duty. I'll be using it for towing my car tilt bed trailer.
# 12
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
Sara R was helpful helping me find the right hitch for what I described as needing. I was excited to see the hitch pin in my order details even though I didn't order it. Sadly, the picture gave me a false impression. Overall, excellent customer service and product.
Working in the sand and grass of my driveway my wife and I installed our new etrailer receiver hitch. Great fit and finish! Went right on as described in the online guide. Hitch required a spacer washer on top back bolt attachment point. Taped it on so it would not move while lifting in place and it stayed right there! Used a car jack to raise up and hold the hitch into the underside of the trunk tighten the bolts and reattached the tail pipe done. Now we can pull our Sunfish Sailboat any where the car will go.
# 13
etrailer 2-3/4" Rise or 4" Drop Ball Mount Kit - 7,500 lbs
It did the trick, although it is starting to rust.
I purchased the etrailer.com 2-3/4 " Rise or 4" Drop Ball Mount Kit, Curt Trailer Hitch Receiver and Twist-in 7-Pole RV-Style Trailer Connector for my 2011 Chevy Silverado. Quick Delivery! All the necessary parts arrived in perfect condition. Directions were spot on and the instructional videos were great.
# 14
Rapid Hitch Adjustable, Aluminum Ball Mount Kit w/ 2 Zinc Balls - 5-1/2" Drop
I pay to receive the product in good condition, my hitch ended up being damaged, I don't know what type of packaging this was, they are supposedly a waoooo site, I ask for my return label and my refund, I
Works flawlessly. I was very excited the day I got home and my Rapid hitch was on the front porch. It came in nice box and was packaged very well. I opened it up and unpacked my rapid hitch and I was very impressed with the quality and precision of this hitch. All of the machining was PERFECT and everything fit together right. I put it in my truck right away. Going down the road with the trailer on and off there is absolutely no rattles, clunks, or jolts. I also love how everything is aluminum or stainless steel, NO RUST. I wish I could've gotten the greaseless model but my boat is too heavy. My only complaint is that it doesn't come with locking pins. With a hitch this expensive I really wish it came with them. Do yourself a favor and order them with your rapid hitch so you don't have to pay for shipping in the future. Other than that great product and I believe it will outlast me.
# 15
Cushioned Ball Mount for 2" Hitches - 4-3/4" Rise - 6" Drop - 10,000 lbs
Solid piece made in USA. Haven’t towed with it yet. Great phone service. Quick shipping. Impressed by how well the drop hitch arrived, many times small dense items don’t fair well in transit. Due to double box plus great heavy box and extra attachments to the box this arrived great. Clearly etrailer has this down.
All of the items arrived on time and not damaged in any way. Excellent quality products.
# 16
Curt Ball Mount for 2" Hitches - 7" Rise, 8-1/4" Drop - 9-3/8" Long - 10,000 lbs
Was needing a 7-8 inch ride for my camper that could sustain a GVW of at least 5000 lbs. Let me say, it’s a hard to find item. Thankfully I called Etraer and with some research, found me the perfect ball mount. It’s heavy duty for a reasonable price.
I had to flip this upside down and put a hitch ball on this to get it to work with my Dodge Journey and my camper. It's held up without issue for a half-dozen camper pulls. I wish the paint hadn't already started flaking off at the receiver end, but that's to be expected when you connect metal to metal. The other parts of this haven't started flaking yet after a year so hopefully it continues to hold up.
# 17
Flash Simple 2-Ball Mount w Chrome Balls - 2" Hitch - 10" Drop, 11" Rise
This is a great product, well built and matches my chrome bumper. My truck is lowered so I needed a sturdy product with a good rise to compensate. This hitch, along with the Roadmaster Quiet Hitch from etrailer and the Fastway Trailer Hitch locks work together nicely.
Looks good and functions even better. I have the hitch fully adjusted and never had an issue. Gotten a ton of compliments! Would highly recommend!
# 18
Convert-A-Ball Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 10,000 lbs
Good, very solid ball mount with just the extra rise I needed, 2 3/4", to get level trailer and good clearance for the trailer jack. But excessive shipping charges from etrailer, $[XX] for an $[XX] purchase. Found out to my cost later that [online vendor] would have shipped for free.
As a full-time RVer, e-shopping is very important for us. etrailer was the right place to shop. Right product, delivered on-time for a great price. You beat the local discount RV store by $25 including shipping. At the same time, I had another outfit send me a clearly inferior product to the one they displayed. Said they would e-mail a pre-paid shipping label for the return (didn't) and tried to put the blame on Amazon. Thanks etrailer for a great experience !
# 19
Convert-A-Ball Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10,000 lbs
Makes for a great hard-core dirt road set up with a 3000 pound trailer, in conjunction with the Curt rocker ball, Towing with an F150 over many miles of washboards, down through washes where the road was washed out, etc. Really makes for a gentler set up on the equipment in the trailer and the truck. Thanks a lot E-trailer!
My usage of your hitch is a bit unusual, I think. I pull a two ton roller with my Ram and I've used your cushioned hitch to smooth out the process. The roller Lunette just dropped over a 2" ball and then banged and jerked on the ball neck. Check out the photos for my adaptation.. I can flip it over and use the 2" ball! Have enclosed some photos. The cushion is holding up very well and it takes a beating!! Thanks
# 20
Channel Style Adjustable Ballmount - 2" & 2-5/16" Balls - 14,000 lbs
Still haven't towed anything with it yet but it seems very solid. I do think it will rattle some in the receiver because it is loose in my 2" receiver on my 2019 F150.
This hitch has worked out great for me over the last year. It’s very heavy duty and easy to adjust. I’ve hauled a 9,000 lb boat, long-distance on numerous occasions without issue. I also haul a landscape trailer on a daily basis weighing over 5,000lbs and haven’t had a single issue. Great hitch that was significantly cheaper than others and is very high quality. I’ve recommended it to several people and I wouldn’t hesitate to buy again. The only thing I would like to have now in a hitch is a tongue weight gauge, but it isn’t necessary.
MaxxTow Adjustable-Height Ball Mount Review - 2013 GMC Yukon
Today on our 2013 GMC Yukon we'll be test fitting the Maxxtow adjustable height ball mount for two-inch hitches with a ten-inch drop or eight-inch rise rated at 5000 pounds, part number MT70067. Before we begin our test fit we will first need to determine the hitch height of our vehicle. This is the measurement from the ground to the inside top of the receiver tube. Our vehicles hitch height is 24 inches. Keep in mind that this measurement may vary due to tire size, hitch style or after-market accessories. We'll begin our test fit by sliding the shank of the ball mount into the opening of the hitch and then securing it with the pin and clip. We can now remove the three pins and flip the platform over in the rise position and secure it again with the two pins.
MaxxTow Ball Mount Review - 2013 GMC Yukon
Today on our 2013 GMC Yukon, we'll be test fitting the MaxxTow ball mount with 2" accessory receiver for 2" hitches, with a 2-1/4" drop, rated at 5,000 lbs., part number MT70066. Before we begin our test fit, we will first need to determine the hitch height of our vehicle. This is the measurement from the ground to the inside top of the receiver tube. Our vehicle's hitch height is 24". Keep in mind that this measurement may vary due to tire size, hitch style, or after-market accessories. Now to begin our test fit, we'll slide the shank of the ball mount into the opening of the hitch, and secure it with the pin and clip.
Draw-Tite Ball Mount Review - 2013 GMC Yukon
Today on our 2013 GMC Yukon we'll be test fitting the Draw Tite Ball Mount with a 3/4 Inch Rise or 2 Inch Drop, rated at 7500 pounds, part number 2923. Before we begin our test fit we will first need to determine the hitch height of our vehicle. This is the measurement from the ground to the inside top of the receiver tube. Our vehicle's hitch height is 24 inches.Keep in mind that this measurement may vary due to tire size, hitch style or aftermarket accessories. We'll now begin our test fit by sliding the shank of the ball mount into the opening of the hitch and securing it with a pin and clip. We'll now measure from the ground to the top of the ball platform.
Diversi-Tech Adjustable Ball Mount Review - 2013 GMC Yukon
Today on our 2013 GMC Yukon we'll be test fitting the DivirsiTech Self Locking Adjustable Aluminum Ball Mount with Two Chrome Balls with a 6 Inch Drop or 7 Inch Rise rated at 10,000 pounds, part number dtalbm6600. Before we begin our test fit we will first need to determine the hitch height of our vehicle. This is the measurement from the ground to the inside top of the receiver tube.Our vehicle's hitch height is 24 inches. Keep in mind that this measurement may vary due to tire size, hitch style or aftermarket accessories. We'll now begin our test fit in the drop position by sliding the shank of the ball mount into the hitch. We can then turn the key to allow the integrated hitch pin to fall into place.Now with the ball mount in the drop position we can then measure from the ground to the top of the ball platform and we'll get a measurement of about 18 inches.
Curt Multi-Ball Adjustable Ball Mount Review - 2013 GMC Yukon
Today on our 2013 GMC Yukon, we'll be test fitting the Curt multi-ball adjustable ball mount for 2" hitches, part number D900. Before we begin our test fit, we will first need to determine the hitch height of our vehicle. This is the measurement from the ground to the inside top of the receiver tube. Our vehicle's hitch height is 24". Keep in mind that this measurement may vary due to tire size, hitch style, or after-market accessories. We'll now begin our test fit by sliding the shank of the ball mount into the opening of the hitch, and securing it with the pin and clip.
Curt Tri-Ball Mount Review - 2013 GMC Yukon
Today on our 2013 GMC Yukon we'll be test fitting the Curt Tri-Ball Mount for 2 Inch Hitches, part number c45001. Before we begin our test fit we will first need to determine the hitch height of our vehicle. This is the measurement from the ground to the inside top of the receiver tube.Our vehicle's hitch height is 24 inches. Keep in mind that this measurement may vary due to tire size, hitch style or aftermarket accessories. We'll begin our test fit by sliding the shank of the ball mount into the opening of the hitch and securing it with a pin and clip. Now this ball mount does feature three different size balls which you can rotate to the right or to the left to access the 1-7/8 inch ball or the 2 inch ball.This ball mount gives you the ability to tow along trailers with different size couplers without the need of different ball mounts.
Convert-A-Ball Ball Mount with 8 Inch Drop Review - 2013 GMC Yukon
Today on our 2013 GMC Yukon we'll be test fitting the Convert-A-Ball Cushion Ball Mount for Two Inch Hitches with a 6-3/4 Inch Rise or 8 Inch Drop rated at 10,000 pounds, part number amsc8. Before we begin our test fit we will first need to determine the hitch height of our vehicle. This is the measurement from the ground to the inside top of the receiver tube.Our vehicle's hitch height is 24 inches. Keep in mind that this measurement may vary due to tire size, hitch style or aftermarket accessories. We'll begin our test fit in the drop position by sliding the shank of the ball mount into the opening of the hitch and securing it with a pin and clip. We'll then measure from the ground to the top of the ball platform and we'll get a measurement of about 16 inches.We can flip the ball mount over into the rise position and again measure from the ground to the top of the ball platform we'll get a measurement of 30-1/2 inches.
Convert-A-Ball Pintle Mounting Bar Review - 2013 GMC Yukon
Today on our 2013 GMC Yukon well be test fitting the Convert-a-Ball cushioned adjustable pintle mounting bar for two-inch hitches rated at 10,000 pounds, part number ampc2. Well begin our test fit by sliding the shank of the mounting bar into the opening of the hitch and securing it with the pin and clip. You can use this in the drop position or flip it over and use it in the rise position which will give you a total of eight different positions to use for the pintle height to level your trailer. And that will complete todays test fit for the Convert-a-Ball cushioned adjustable pintle mounting bar for two-inch hitches rated at 10,000 pounds, part number ampc2 on our 2013 GMC Yukon.
Convert-A-Ball Cushioned Pintle Hook Combo Review - 2013 GMC Yukon
Today on our 2013 GMC Yukon well be test fitting the Convert-a-Ball cushioned pintle hook combo with three nickel-plated balls for 2-inch hitches rated at 16,000 pounds, part number ph2. Before we begin our test fit, we will first need to determine the hitch height of our vehicle. This is the measurement from the ground to the inside top of the receiver tube. Our vehicles hitch height is 24 inches. Keep in mind that this measurement may vary due to tire size, hitch style, or after-market accessories. Well begin our test fit by sliding the shank of the carrier into the opening of the hitch and securing it with the pin and clip.
Convert-A-Ball Dual-Cushioned Adjustable Ball Mount Review - 2013 GMC Yukon
Today on our 2013 GMC Yukon, we'll be test fitting the Convert-A-Ball cushioned adjustable ball mount with a 7" rise to a 9" drop, rated at 5,000 lbs., part number CAB-UM. Before we begin our test fit, we will first need to determine the hitch height of our vehicle. This is the measurement from the ground to the inside top of the receiver tube. Our vehicle's hitch height is 24". Keep in mind that this measurement may vary due to tire size, hitch style, or after-market accessories. Now in the drop position, we'll slide the shank of the ball mount into the opening of the hitch and secure it with the pin and clip.
Convert-A-Ball 6-Way Multi-Hitch Ball Mount Review - 2013 GMC Yukon
Today on our 2013 GMC Yukon well be test fitting the Convert-a-ball cushioned 6-way multi-hitch ball mount for 2-inch hitches rated at 10,000 pounds, part number cab-6w. Before we begin our test fit we will first need to determine the hitch height of our vehicle. This is the measurement from the ground to the inside top of the receiver tube. Our vehicles hitch height is 24 inches. Keep in mind that this measurement may vary due to tire size, hitch style, or after-market accessories. Well begin our test fit by sliding the shank of the ball mount into the opening of the hitch, and securing it with a pin and clip.
Convert-A-Ball Heavy Duty Ball Mount with 2 Inch Drop Review - 2013 GMC Yukon
Today on our 2013 GMC Yukon well be test fitting the Convert-a-ball cushioned ball mount for 2-inch hitches with a 1-inch rise or 2-inch drop rated at 14,000 pounds, part number amsc2hd. Before we begin our test fit we will first need to determine the hitch height of our vehicle. This is the measurement from the ground to the inside top of the receiver tube. Our vehicles hitch height is 24 inches. Keep in mind that this measurement may vary due to tire size, hitch style, or after-market accessories. Well now begin our test fit in the drop position by sliding the shank of the ball mount into the opening of the hitch, and securing it with the pin and clip.
Convert-A-Ball Ball Mount with 2 Inch Drop Review - 2013 GMC Yukon
Today on our 2013 GMC Yukon well be test fitting the Convert-a-ball cushioned ball mount for 2-inch hitches with a 3/4-inch rise or 2-inch drop rated at 10,000 pounds, part number amsc2. Before we begin our test fit we will first need to determine the hitch height of our vehicle. This is the measurement from the ground to the inside top of the receiver tube. Our vehicles hitch height is 24 inches. Keep in mind that this measurement may vary due to tire size, hitch style, or after-market accessories. Well now begin our test fit by sliding the shank of the ball mount in the drop position into the opening of the hitch.
Andersen Rapid Hitch Ball Mount Review - 2013 GMC Yukon
Today on our 2013 GMC Yukon well be test fitting the Rapid Hitch Adjustable Aluminum Ball Mount Kit with two chrome balls, part number am3410. Before we begin our test fit we will first need to determine the hitch height of our vehicle. This is the measurement from the ground to the inside top of the receiver tube. Our vehicles hitch height is 24 inches. Keep in mind that this measurement may vary due to tire size, hitch style, or after-market accessories. Well begin our test fit with the ball mount in the drop position by sliding the shank into the opening of the hitch, and securing it with a pin and clip.
What our customers are saying:
"Great service........thanks"